HomeHome > FC / ESC Stacks > FETTEC FC-G4 Stacks

FETTEC FC-G4 & FETTEC 4in1 45A ESC STACK

Item Code:
20171
Latest STM32G4 Processor /KISS FC Firmware /2S-6S Lipo /Onboard OSD
Supports Dshot 300-2400,OneShot 42/125, PWM, Crossfire, SBUS.
Unit Price:
USD $160.99
Price:
USD
$160.99
Shipping Cost:
to
PC
  • Product Details

Holybro FETtec FC G4

Description:

The Holybro FETtec FC G4 features the latest STM32 G4 MCU with math accelerator for the ultimate in-flight performance, onboard OSD for KISS flight tuning, 2 dedicated BECs for 5V and 16V switchable power, DSHOT2400 outputs for support of up to 8 motors, and dual 20x20 and 30x30 mounting holes.

Note:

Currently, the Holybro Fettec FC G4 does not support BLHeli_32 ESC Configuration via FC Passthrough and BLHeli_32 ESC telemetry/current reading. An Betaflight Flight Controller is needed to configure BLHeli32 ESC Setting.  

 Specification

  • Latest STM32G4 Processor
    • 170Mhz + Math accelerator
    • MPU6000
  • Supply voltage 6-27V (2S-6S Lipo)
  • 2x dedicated onboard BEC (max. 600mA each)
    • 5V BEC for RX
    • 5V/16V BEC for VTX (switchable and real Pit*)
  • 2x 8 pin connector for solder free ESC connection
    • Connector 1: ESC signal 1-4, telemetry, VCC, GND
    • Connector 2: ESC signal 5-8 (depending on UAV type 1-4), telemetry, VCC, GND
  • 1x 8 pin connector for solder free VTX, cam connection and OSD or digital systems
    • real Pit* VCC, GND, Video in, Video out, BEC 5V/16V, VCS/TX3, RX3
  • 2x 6 pin connectors for serials
    • RX1, TX1, 3.3V, VCC, 5V, GND
    • RX3, VCS/TX3, RGB LED, VCC, 5V, GND
  • 1x 4 pin connector for receiver
    • Signal, TLM, 5V, GND
  • 5 UART serials
    • UART 1 free
    • UART 2 used for Receiver
    • UART 3 free
    • UART 4 used for onboard OSD, can be set free
    • UART 5 used for ESCs / TLM / Onewire
  • 4 ESC solder pads (Signal/GND) in each corner
  • Buzzer pads
  • 4 tiny RGB LEDs (selectable color)
  • Supported ESC protocols
    • PWM, Oneshot125, Oneshot42, Dshot150/300/600/1200/2400, FETtec Onewire
  • FETtec KISS firmware
  • Onboard OSD
    • Graphic OSD (STM32)
    • Full KISS Tuning
    • Filter (PIDs, Rates, Settings)
    • LED control (RGB LED, Racewire)
    • VTX
    • Live data graphs (Voltage, motor rpm, current, motor temp, gyro values, link quality)
    • KISS GPS support + live map
    • Custom graphic pilot logo
    • Stick overlay
    • Custom layout
    • can be deactivated for usage of digital systems
  • Connector type: JST-SH-1mm

PINMAP

FETtec 4in1 45A ESC

The FETtec 45A 3-6S ESC is a powerful 4-in-1 electronic speed controller that has a mounting pattern of 30.5x30.5 and supports Dshot 300-2400, OneShot 42/125, PWM, Crossfire, SBUS, and other features!

Specifications

  • Active current limiting @ 45A
  • Input voltage: 3S-6S
  • High-quality 40V MOSFETs
  • STM32G071 @ 64MHz
  • 128 kHz Motor PWM
  • Full sine wave control
  • Soldering holes for up to 5 additional capacitors
  • KISS FC Passthrough
  • Betaflight Passthrough (available in 4.1)
  • Automatic input signal detection:
    • Dshot 300-2400
    • PWM
    • OneShot 42/125
    • OneWire BUS with up to 8kHz loop time (one cable for all Motorsignals and Telemetry)
    • In development: Crossfire, SBUS
  • 38 mm x 38 mm
  • Mounting hole: 30.5 mm x 30.5 mm, M3 expandable to M4

Diagram

Includes

  • 1 x FETTEC FC G4 Stack
  • 1 x Electrolytic capacitor: 470uF 50v
  • 1 x JST SH8P-8P Cable
  • 1 x JST SH8P Cable
  • 1 x JST SH6P Cable