HomeHome > FC / ESC Stacks

Kakute F4 AIO V2 + Atlatl HV V2 Stack

Item Code:
20036
Flight Tower
Unit Price:
USD $65.00
Price:
USD
$65.00
Shipping Cost:
to
PC
50 in Stock
  • Product Details
  • Write a Comment(0)
  • After-sales Service
Kakute F4 All-In-One V2

New V2 Features
·       Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, etc.
·       Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.
·       Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
·       Barometer sensor on board allows altitude hold mode.
·       I2C pad available for certain external sensors.

Features

·       Supports Betaflight and Cleanflight.
·       Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
·       Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
·       New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
·       2 oz. copper PCB allows up to 120A maximum continuous current.
·       Dedicated bootloader button for easy firmware flashing.
·       Low-profile design fits into even very compact frames.
·       Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
·       Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.
·       Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
·       Supports BLHeli pass-through for easy ESC upgrade and configuration. 

Specifications

·       MCU: STM32F405RGT6 32-bit processor
·       IMU: ICM20689 (SPI)
·       Barometer: BMP280
·       USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
·       5 hardware UARTS (UART1,3,4, 5, 6)
·       Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
·       128 Mbit Dataflash chip for Blackbox logging
·       Dimensions: 35x43x7mm (includes USB in height)
·       Mounting Holes: Standard 30.5mm square to center of holes 
·       Weight: 7g


ATLATL HV V2

Features

  • Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.

  • Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.

  • SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.

  • All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.

  • MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.

  • LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.

  • Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.

  • 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.

  • Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.

  • Standard 36mm form factor allows you to mount the Atlatl directly on your flight controller stack.

Specifications

  • Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
  • Audio: 6.5 MHz Mono
  • Antenna Connector: MMCX
  • Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
  • Dimensions: 35x25x7mm (Includes USB height)
  • Mounting Holes: Standard 30.5mm square to center of holes 
  • Weight: 9.3g

Package include

Kakute F4 ALL V2+Atlatl stack *1 
80mm SMA--MMCX Cable *1 
150mm 4pin JST GH wire *1

FFC*1
Foam*1

Manual:

http://www.holybro.com/manual/Holybro-Atlatl-HV-v2-Manual.pdf
http://www.holybro.com/manual/Holybro_Kakute_F4_AIO_V2_Manual.pdf
Maybe You Also Like...
Kopis cinewhoop_2.5inch(free shipping)
NEW
Caddx Nebula Vista Kit 720p/120fps low latency HD digital FPV system / T-Motor: F1404 KV3800 / GEMFAN D63-5B / Take-off Weight:248g
$144.00
Tekko32 F3 4IN1 Mini 35A ESC(35A)
NEW
BLHELI32 / F3 MCU/4x 35A/20x20mm
$43.00
H-RTK F9P GNSS Series
NEW
Differential high-precision multi-band GNSS positioning system series. UBLOX F9P module
$378.00
H-RTK M8P GNSS Series
NEW
H-RTK M8P is the latest differential high-precision GNSS positioning system from Holybro. It uses a UBLOX M8P module.
$199.00
Pix32 v5
HolyBro Pix32 v5 is a new flight controller we have developed on the base of FMUv5 scheme, which can be regarded as a variant version of ‘Pixhawk4’.
$143.00
Durandal
Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.
$205.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00
Kakute F7 HDV Stacks
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module.
$92.00
KakuteF7 HDV AIO
Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module.
$42.00
X500 Kit
X500 Frame full carbon fiber twill,ARM diamete16mm, It is  perfectly compatible with the Holybro Pixhawk4 and Pixhawk4 Mini kits.The kit is easy to assemble.No soldering needed.
$425.00