HomeHome > FC / ESC Stacks

Kakute F4 V2 & Tekko32 ESC STACK

Item Code:
20064,20065
The latest tekko32 45A 4in1 ESC has got some improvements on its performance
Unit Price:
USD $86.00
Price:
USD
$86.00
Shipping Cost:
to
Delivery:
Estimated between
PC
199 in Stock
  • Product Details
  • Write a Comment(0)
  • After-sales Service

 

Kakute F4 V2

Descriptions:

The HolybroKakute F4 All-In-One flight controller makes it easy to build your multirotor. It integrates flight controller (FC), power distribution board (PDB), and on-screen display (OSD) in one. The Kakute F4 V2’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy.

New V2 Features

· Additional UART (UART 4) added to support serial camera communication such as to RunCam Split. Please note this is NOT the same as Betaflight Camera Control feature, which controls the menu of FPV cameras like Swift, etc.
· Additional UART (UART 5) added to support ESC telemetry such as from BLHeli_32 and KISS.
· Through-hole solder pads instead of flat pads for more secure soldering especially for beginners.
· Barometer sensor on board allows altitude hold mode.
· I2C pad available for certain external sensors.

Features

· Supports Betaflight and Cleanflight.
· Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
· Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
· New high-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz.
· Dedicated bootloader button for easy firmware flashing.
· Low-profile design fits into even very compact frames.
· Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
· Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 AIO monitors voltage directly from the battery power lead.
· Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 1.5 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
· Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

· MCU: STM32F405RGT6 32-bit processor
· IMU: ICM20689 (SPI)
· Barometer: BMP280
· USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
· 5 hardware UARTS (UART1,3,4, 5, 6)
· Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
· 128 Mbit Dataflash chip for Blackbox logging
· Dimensions: 35x30x8mm (includes USB in height)
· Mounting Holes: Standard 30.5mm square to center of holes
· Weight: 7g


Tekko32F3 4in1 45A ESC

The latest tekko32 45A 4in1 ESC has got some improvements on its performance:
1) Enhanced BEC, withstand voltage up to 80V.
2)The first blheli32 ESC in the market with default PWM output 96K giving you smoother and quieter experience.
3) Amperage meter scale ratio has been adjusted to 185-195.
4) The mounting hole has been changed into M4 with anti-vibration silicone grommet Insert.
5)The PCB design uses a design in which the drive circuit and the control circuit are separated. This design broadens the overcurrent capability of the drive circuit, and at the same time reduces the electrical interference to the control circuit.

Features:

  • 32bit ESC with BLHELI32 firmware
  • Supports 3-6S lipo input
  • PWM input, TLM supported
  • Voltage output (VBAT)
  • NO BEC
  • Supports oneshot / Multishot / Dshot PWM
  • Mounting holes 30.5x30.5mm
  • Supports damped light
  • F3 MCU, runs double faster than F051
  • Extra Cap needed for high current or 6s usage
  • Dimensions: 44x37x6mm
  • Weight: 13.6g

 Pin MAP:

Atlatl

Features

  • Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.

  • Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.

  • SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.

  • All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.

  • MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.

  • LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.

  • Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.

  • 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.

  • Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.

  • Standard 36mm form factor allows you to mount the Atlatl directly on your flight controller stack.

Specifications

  • Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
  • Audio: 6.5 MHz Mono
  • Antenna Connector: MMCX
  • Input Voltage: 7 to 28 volts (2-6S LiPo) with absolute maximum 42 volts
  • Dimensions: 35x25x7mm (Includes USB height)
  • Mounting Holes: Standard 30.5mm square to center of holes 
  • Weight: 9.3g

Package include

Kakute f4 stack *1
Electrolytic capacito: 1000uF 35v *1
8pin to 8pin 1mm pitch 65mm cable *1
8pin to 8pin 1mm pitch 25mm cable *1
80mm SMA--MMCX Cable *1 (
Optional)
150mm 4pin JST GH wire *1 (
Optional)

Manual:

KakuteF4V2 Manual.pdf
Atlatl-HV-v2-Manual.pdf
Tekko32 F3 4in1 ESC(45A) SPEC

 

Maybe You Also Like...
Durandal
Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.
$205.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
SALE
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00 $170.00
Kakute F7 HDV Stacks
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$92.00
KakuteF7 HDV AIO
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$42.00
Kakute F7 AIO V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$49.00
Kakute F7 V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$45.00
KakuteF7 HDV
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$38.00
Pixhawk 4 GPS Module
SALE
Pixhawk 4 GPS Module with JST GH 10 Pin connector for Pixhawk 4 "GPS Module" input port
$42.00 $42.00
Kakute F4 All-In-One V2
The Holybro Kakute F4 AIO All-In-One flight controller makes it easy to build your multirotor.
$40.00
Kakute F4 V2
The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot.
$36.00
Pix32"Pixhawk" Flight Controller
This board is based on the Pixhawk project FMUv2 open hardware design. It is also know as Pixhawk 2,with hardware version px4 2.4.6.
$129.00