HomeHome > FC / ESC Stacks > Kakute F4 mini Stacks

Kakute F4 V2 mini Stacks

Item Code:
20107,20108
Unit Price:
USD $67.00
Price:
USD
$67.00
Shipping Cost:
to
PC
395 in Stock
  • Product Details
  • Write a Comment(0)
  • After-sales Service

Kakute F4 V2 Mini

The Holybro Kakute F4 V2mini flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The faster F4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization! Because of issues with serial inversion, other F4 boards struggle to support protocols such as FrSky SBUS and SmartPort at the same time. The Kakute F4 V2mini is designed to support all serial protocols at once.

Features

• Supports Betaflight and Cleanflight.
• Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
• High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.
• Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.
• Dedicated bootloader button for easy firmware flashing.
• Low-profile design fits into even very compact frames.
• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 V2mini monitors voltage directly from the battery power lead.
• On-board regulators output 5v at up to 1.0 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
• Supports BLHeli pass-through for easy ESC upgrade and configuration.
• 2 Additional PWM output, can be used for Camera control , motor5 or motor6 after resourced.

Specifications

• MCU: STM32F405RGT6 32-bit processor
• IMU: MPU6000 (SPI)
• Barometer: BMP280
• USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
• 5 hardware UARTS (UART1,3,4, 5, 6)
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
• 128 Mbit Dataflash chip for Blackbox logging
• Dimensions: 32x29x6mm (includes USB in height)
• Mounting Holes: Standard 20mm square to center of holes
• Weight: 4.4g

Pinout Diagram:

Tekko32 F3 4IN1 Mini 35A ESC

BLHELI32 / F3 MCU/4x 35A
The New BLHELI32 ESC adapted the F3 MCU, which will provide a smoother control and faster response speed. 4x 35A F3 BLHELI32 ESC in 20×20 standard .

SPEC:

  • F3 MCU, double the speed of F051, the MCU works at 108Mhz
  • 32bit ESC with BLHELI32 firmware
  • Supports 3-6S lipo input
  • Default PWM output 96K
  • Amperage meter scale ratio has been adjusted to 185.
  • PWM input, TLM supported
  • Voltage output (VBAT)
  • NO output BEC
  • Supports oneshot / Multishot / Dshot PWM
  • Supports damped light
  • Ext. cap needed for 6s (1000uf 35v for 6s usage.)
  • Mounting holes: 20x20mm(M3)
  • Size:32 x 38 mm
  • Weight: 8g

PIN MAP:

This motor idle throttle value can be adjusted in Betaflight configuration, under ESC/Motor Features.
When using dshot, the motor idle throttle value is recommended to be adjusted to “10” percent.

 

Atlatl HV Micro

Features

  • Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
  • Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
  • SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
  • All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.
  • MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.
  • LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.
  • Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
  • 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
  • Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.
  • Standard 26mm form factor allows you to mount the Atlatl directly on your flight controller stack.

Specifications

  • Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
  • Audio: 6.5 MHz Mono
  • Antenna Connector: MMCX
  • Input Voltage: 7 to 28 volts (2-6S LiPo)
  • Dimensions: 30x26x7mm
  • Mounting Holes: Standard 20mm square to center of holes
  • Weight: 3.6g

Package Includes:

SKU20107 Kakute F4 V2 mini & Tekko32 F3 4in1 35A mini ESC Stack

Kakute F4 V2 Min Stack *1
Electrolytic capacito: 1000uF 35v *1
JST SH 8pin to 8pin 65mm cable *1
JST SH 8pin to 8pin 25mm cable *1
JST SH 6pin 150mm cable*1 ( The cable that goes to the CADDX Vista Air Unit is included.)
JST SH 6pin to GH 8pin 150mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
JST SH 6pin to GH 8pin 80mm cable*1  ( The cable that goes to the DJI Air Unit is included.)

SKU20108 Kakute F4 V2 mini & Tekko32 F3 4in1 35A mini ESC  & ATLATL HV Micro  Stack

Kakute F4 V2 Mini Stack *1
Electrolytic capacito: 1000uF 35v *1
JST SH 8pin to 8pin 65mm cable *1
JST SH 8pin to 8pin 25mm cable *1
JST SH 6pin 150mm cable*1 ( The cable that goes to the CADDX Vista Air Unit is included.)
JST SH 6pin to GH 8pin 150mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
JST SH 6pin to GH 8pin 80mm cable*1  ( The cable that goes to the DJI Air Unit is included.)
80mm SMA–MMCX Cable *1
60mm Antenna *1
150mm 4pin JST GH wire *1

Manual:

Holybro Kakute F4 V2 mini Manual 
Tekko32 F3 4in1 mini ESC(35A) SPEC
Holybro_Atlatl_HV_micro_Manual

Some Tips:

BLHeli_32 ESC Firmware Overview
GitHub