HomeHome > Flight Controllers > Kakute

Kakute F4 V2.3

Item Code:
The Holybro Kakute F4 V2 Mini flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. Mounting Holes: 30.5x30.5mm
Unit Price:
USD $41.99
Shipping Cost:
  • kakute F4 v2.3 w/ 4ct 1404 Motors
Kakute F4 V2.3
Quantity: 1
The select 1 products
  • Product Details
The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot. The faster F4 processor gives room for future feature development: run all features at the fast 8 kHz PID loop rate, at single-digit CPU utilization! Because of issues with serial inversion, other F4 boards struggle to support protocols such as FrSky SBUS and SmartPort at the same time. The Kakute F4 is designed to support all serial protocols at once.


  • Supports Betaflight and Cleanflight.
  • Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
  • High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.
  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.
  • Dedicated bootloader button for easy firmware flashing.
  • Low-profile design fits into even very compact frames.
  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F4 V2 monitors voltage directly from the battery power lead.
  • On-board regulators output 5v at up to 1.0 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
  • On-board regulators output 9v at up to 2A to power DJI VTX.
  • 6 PIN JST GH connector for DJI VTX.
  • Supports BLHeli pass-through for easy ESC upgrade and configuration.
  • 2 Additional PWM output, can be used for Camera control , motor5 or motor6 after resourced. (PB6 [B06 in Betaflight]<-> M5, PB7 [B07 in Betaflight]<-> M6)


  • MCU: STM32F405RGT6 32-bit processor
  • IMU: MPU6000 (SPI)
  • Barometer: BMP280
  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
  • 5 hardware UARTS (UART1,3,4, 5, 6)
  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
  • 128 Mbit Dataflash chip for Blackbox logging
  • Dimensions: 36.8x36.8x8mm
  • Mounting Holes: 30.5x30.5mm(M4) 
  • Weight: 7.4g

Pinout Diagram:

Package Includes:

   FC board *1
   M3 Anti-Vibration Silicone Grommet Insert *4
   JST SH 8pin 150mm cable*1 
   JST GHR 8pin to JST GHR 6pin 80mm cable*1 
   JST GHR 8pin to JST GHR 6pin 150mm cable*1


Kakute F4 V2.3 Manual

More relevant product options