HomeHome > FC / ESC Stacks > Kakute F7 Stacks

Kakute F7 & Tekko32 F3 Metal 4in1 ESC Combo

Item Code:
20060
Sold: 66
Kakute F7 & Tekko 32 F3 Metal 4in1 esc (BLHeli 32) Combo
Unit Price:
USD $116.00
Price:
USD
$116.00
Shipping Cost:
to
Delivery:
Estimated between
PC
1 in Stock
  • Product Details
  • Reviews(0)
  • Write a Comment
  • After-sales Service

Tekko32F3 Metal 4in1 ESC

BLHELI32 / Onboard analog current sensor / F3 MCU

New BLHELI32 ESC with F3 MCU, give more smooth control and faster responding speed. using metal case mosfet for better Heat dissipation. We tested in short time on 220A intotal. The actual performance will only limited by the air flow.

SPEC:

  • F3(M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108Mhz
  • The 4in1 has onboard analog current sensor, and TLM function(then no current reading over TLM)
  • Using metal case mosfet for better Heat dissipation
  • Supports Lipo 4-6S
  • Ext. cap needed for 6s (470uf 35v for 6s usage.)
  • Size:42 x 42 mm
  • Mounting holes:30.5x30.5mm
  • Weight: 12g
Notice:
The air flow is very import if you want to run this 4in1 in high current.
The input cable(from lipo to 4in1), should be good soldered, and at least 12AWG
 

Package included:
Tekko32 F3 Metal 4in1 ESC *1
Electrolytic capacito: 470uF 35v *1
8pin to 8pin 1mm pitch 65mm cable *1
8pin to 8pin 1mm pitch 25mm cable *1
 

PIN MAP:

Warning:
Please use non-metallic isolation standoffs (marked in red in the diagram above) for the mounting holes on the ESC, Because mounting holes and motor pad are connected.
 

Some Tips:

Kakute  F7

The Holybro Kakute F7 flight controller makes it easy to build your multirotor. It integrates flight controller (FC) and on-screen display (OSD) in one. The Kakute F7’s layout makes it easy to wire up the other components of the multirotor while keeping the build neat and tidy.

Features
• Supports Betaflight, Butterflight, and Cleanflight.
• Betaflight OSD. Change PIDs, adjust common configuration parameters, and change video transmitter channel and power level, all using your transmitter sticks and goggles.
• Soft-mounting built in. The IMU (“gyro”) chip on this board is mounted on vibration-isolating foam. This means that there is no need to soft-mount the board itself.
• High-performance / low-noise / high sensitivity IMU. ICM20689 with 6-axis gyro and accelerometer. Can run at up to 32 kHz sampling rate.
• Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA pads for use with external GPS/magnetometer units.
• 2 oz. copper PCB allows up to 120A maximum continuous current.
• Dedicated bootloader button for easy firmware flashing.
• Low-profile design fits into even very compact frames.
• Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
• Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the Kakute F7 monitors voltage directly from the power supply.
• Filtered voltage output for clean, noise-free video. On-board regulators output 5v at up to 2 amps and 3.3v at up to 200 mA to power peripherals such as receiver, video transmitter, FPV camera, or LED strip.
• Supports BLHeli pass-through for easy ESC upgrade and configuration.


Specifications
• MCU: STM32F745 32-bit processor
• IMU: ICM20689 (SPI)
• Barometer: BMP280
• Current Sensor: Approximately 130 amps maximum measurable value
• USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
• 6 hardware UARTS (UART1,2,3,4,6,7)
• All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
• Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
• TF card for Blackbox logging

• Dimensions: 35x41x7mm (includes foam-mounted gyro board in height)
• Mounting Holes: Standard 30.5mm square to center of holes
• Weight: 9g




Manual:

http://www.holybro.com/manual/Holybro_Kakute_F7_Manual.pdf

 
 
 
 
 
 
 
 
Average rating:

Maybe You Also Like...
Kopis mini_3inch(free shipping)
KOPIS is a high-performance ready-to-fly FPV racing drone from Holybro,
$179.00
X500 Kit
X500 Frame full carbon fiber twill,ARM diamete16mm, It is  perfectly compatible with the Holybro Pixhawk4 and Pixhawk4 Mini kits.The kit is easy to assemble.No soldering needed.
$425.00
X500 Frame Kit
Perfectly compatible with the Pixhawk4 set&Pixhawk4 mini set.
$86.00
Kopis2 6S V2(free shipping)
On Holybro Kopis 6S V2, the ESC installation direction has been changed while the power supply cord has been moved from the side of the quad to the tail, which will better protect the ESC. Kopis 6S V2 is equipped with a 1200TVL Foxeer Micro Razer FPV cam
$299.00
Kakute F7 V1.5& ATLATL HV V2 & Tekko 32 F3 4in1 45A ESC Combo
The latest tekko32 45A 4in1 ESC has got some improvements on its performance: 1) Enhanced BEC, withstand voltage up to 80V. 2)The first blheli32 ESC in the market with default PWM output 96K giving you smoother and quieter experience. 3) Current meter
$125.00
Kakute F7 V1.5 &Tekko 32 F3 4in1 45A esc  Combo
The latest tekko32 45A 4in1 ESC has got some improvements on its performance: 1) Enhanced BEC, withstand voltage up to 80V. 2)The first blheli32 ESC in the market with default PWM output 96K giving you smoother and quieter experience. 3) Current meter
$100.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
SALE
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00 $170.00
Kakute F4 V2 & Tekko32 F3 4in1 45A ESC STACK
The latest tekko32 45A 4in1 ESC has got some improvements on its performance: 1) Enhanced BEC, withstand voltage up to 80V. 2)The first blheli32 ESC in the market with default PWM output 96K giving you smoother and quieter experience. 3) Current meter
$86.00
Kakute F7 V1.5 Stack
IMU updated to MPU6000,Re-designed and more reliable damping structure
$69.00
Kakute F7 V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$45.00
KakuteF7 HDV
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$38.00