HomeHome > FC / ESC Stacks > Kakute F7 Stacks

Kakute F7 HDV AIO Combo

Item Code:
20091,20092
Unit Price:
USD $99.00
Price:
USD
$99.00
Shipping Cost:
to
Delivery:
Estimated between
set
400 in Stock
  • Product Details
  • Write a Comment(0)
  • After-sales Service

The port to the DJI air unit on KAKUTE F7 HDV and KAKUTE F7 HDV AIO have been optimized, the output voltage has increased to 9V/2A.

Kakute F7 HDV AIO

Overview

Holybro Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV AIO to the DJI FPV VTx, for both signal and power supply.

Features

  • Supports Betaflight.

  • High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.

  • Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.

  • Dedicated bootloader button for easy firmware flashing.

  • Low-profile design fits into even very compact frames.

  • 2 oz. copper PCB allows up to 120A maximum continuous current.

  • Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).

  • Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV AIO monitors voltage directly from the power supply.

  • Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 8V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 8V output up to 2A to DJI FPV VTx.

  • Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

  • MCU: STM32F745 32-bit processor

  • IMU:MPU6000

  • Barometer: BMP280

  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)

  • 6 hardware UARTS (UART1,2,3,4,6,7)

  • All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.

  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.

  • TF card for Blackbox logging

  • Dimensions: 45x37mm

  • Mounting Holes: Standard 30.5mm square to center of holes 

  • Weight: 10g

Manual:


Tekko32 F3 ESC(35A)

Using F3 MCU, with ws2812b LED and current sensor, supports BLHELI32 telemetry function.

Feature:

  • Small size/low weight

  • Build in Current sensor

  • Voltage output (VBAT), ESC Telemetry(TELEM)

  • Supports Oneshot / Multishot / Dshot

  • 32bit ESC with BLHELI32 firmware

  • On-Board RGB LED (WS2812B LED)

  • Auto Timing Feature

  • Smooth Response

SPEC:

  • Power input:3-6s LIPO

  • Cont.Current:35A

  • Size:15*30*5 mm

  • Weight: 3.6g (1pcs)

Tekko32 F3 Metal ESC (65A)

BLHELI32 / Current sensor / 6S / 65 A / F3 MCU
The New BLHELI32 ESC adapted the F3 MCU, which will provide a smoother control and faster response speed, along with a Metal case mosfet that increases Heat dissipation.

The latest Tekko32 F3 Metal ESC has got improvements on both performance and appearance. Enhanced BEC, withstand voltage up to 80V.

SPEC:

  • F3(M4 Core) MCU, Runs BLHELI32 firmware, the MCU works at 108Mhz

  • Mosfet tested at 4S 65A, under props, nothing covered for 1min

  • Supports Lipo 3-6S

  • Ext. cap needed for 6s (330uf 35v for 6s usage.)

  • Onboard WS2812B LED

  • Size:18 x 27 mm

  • Weight: 4.4g (1pcs)

Some Tips:


Package Includes:

FC board *1
M3 Anti-Vibration Silicone Grommet Insert *4

JST GHR 8pin to JST GHR 6pin 80mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
JST GHR 8pin to JST GHR 6pin 150mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
Tekko32 F3 Metal ESC(65A) *4 (Optional)

Tekko32 F3  ESC(35A) *4 (Optional)
Electrolytic capacito: 330uF 35v *4
24AWG 100mm Black wire *1
24AWG 100mm White wire *1
24AWG 100mm Blue wire *1
16AWG 100mm Red wire *1
16AWG 100mm Black wire *1

Maybe You Also Like...
Durandal
Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.
$205.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
SALE
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00 $170.00
Kakute F7 HDV Stacks
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$92.00
KakuteF7 HDV AIO
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$42.00
Kakute F7 AIO V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$49.00
Kakute F7 V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$45.00
KakuteF7 HDV
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$38.00
Pixhawk 4 GPS Module
SALE
Pixhawk 4 GPS Module with JST GH 10 Pin connector for Pixhawk 4 "GPS Module" input port
$42.00 $42.00
Kakute F4 All-In-One V2
The Holybro Kakute F4 AIO All-In-One flight controller makes it easy to build your multirotor.
$40.00
Kakute F4 V2
The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot.
$36.00
Pix32"Pixhawk" Flight Controller
This board is based on the Pixhawk project FMUv2 open hardware design. It is also know as Pixhawk 2,with hardware version px4 2.4.6.
$129.00