HomeHome > FC / ESC Stacks > Kakute F7 mini Stacks

Kakute F7 mini V3 Stacks

Item Code:
20101,20102,20103
Kakute F7 mini V3: DJI FPV Air Unit Supported/MCU: STM32F722/IMU: MPU6000/Mounting Holes:20x20mm
Unit Price:
USD $52.00
Price:
USD
$52.00
Shipping Cost:
to
Delivery:
Estimated between
PC
599 in Stock
  • Product Details
  • Write a Comment(0)
  • After-sales Service


Kakute F7 mini V3

Specifications:

  • MCU: STM32F722RET6 32-bit processor,216MHz, 256Kbytes RAM, 512Kbytes Flash

  • IMU: MPU6000 (SPI)

  • Barometer: BMP280

  • USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)

  • 5hardware UARTS (UART1,2,3,4,6)

  • Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.

  • Onbord 16Mbytes for Blackbox logging

  • 5V Power Out: 1.0A max

  • 3.3V Power Out: 0.2A max

  • Dimensions: 30x30mm

  • Mounting Holes: Standard 20mm square to center of holes 

  • Weight: 4g

Pinout Diagram:

Tekko32 F3 4in1 mini ESC(45A)

The latest Tekko32 F3 4in1 mini ESC has got some improvements on its performance

The PCB design uses a design in which the drive circuit and the control circuit are separated. This design broadens the overcurrent capability of the drive circuit, and at the same time reduces the electrical interference to the control circuit.

BLHELI32 / F3 MCU/4x 45A

The New BLHELI32 ESC adapted the F3 MCU, which will provide a smoother control and faster response speed, 
4x 45A F3 BLHELI32 ESC in 20x20 standard .

SPEC:

  • F3 MCU, double the speed of F051
  • 32bit ESC with BLHELI32 firmware
  • Supports 3-6S lipo input
  • Default PWM output 96K
  • Amperage meter scale ratio has been adjusted to 185.
  • PWM input, TLM supported
  • Voltage output (VBAT)
  • NO output BEC
  • Supports oneshot / Multishot / Dshot PWM
  • Supports damped light
  • Ext. cap needed for 6s (1000uf 35v for 6s usage.)
  • Mounting holes: 20x20mm(M3)
  • Size:32 x 38 mm
  • Weight: 8g

PIN MAP:

 

Atlatl HV micro

Features

  • Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.

  • Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.

  • SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.

  • All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.

  • MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.

  • LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.

  • Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.

  • 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.

  • Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.

  • Standard 26mm form factor allows you to mount the Atlatl directly on your flight controller stack.

Specifications

  • Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
  • Audio: 6.5 MHz Mono
  • Protocol:smart audio2.0
  • Antenna Connector: MMCX
  • Input Voltage: 7 to 28 volts (2-6S LiPo)
  • Dimensions: 30x26mm
  • Mounting Holes: Standard 20mm square to center of holes (M3)
  • Weight: 3.6g

Package Includes:

#20101 Kakute F7 mini V3 & Atlatl Micro VTx STACK
Kakute F7 mini V3 STACK *1
JST SH 8pin 150mm cable*1
JST SH 6pin 150mm cable*1 ( The cable that goes to the CADDX Vista Air Unit is included.)
JST SH 6pin to GH 8pin 150mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
JST SH 6pin to GH 8pin 80mm cable*1  ( The cable that goes to the DJI Air Unit is included.)
80mm SMA--MMCX Cable *1
60mm Antenna *1
150mm 4pin JST GH wire *1

#20102 Kakute F7 mini V3 & Tekko32 F3 4in1 mini ESC(45A) STACK
Kakute F7 mini V3 STACK *1
Electrolytic capacito: 1000uF 35v *1
8pin to 8pin 1mm pitch 65mm cable *1
8pin to 8pin 1mm pitch 25mm cable *1
JST SH 6pin 150mm cable*1 ( The cable that goes to the CADDX Vista Air Unit is included.)
JST GHR 8pin to JST GHR 6pin 80mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
JST GHR 8pin to JST GHR 6pin 150mm cable*1  ( The cable that goes to the DJI Air Unit is included.)

#20103 Kakute F7 mini V3 & Tekko32 F3 4in1 mini ESC(45A) & Atlatl Micro VTx STACK
Kakute F7 mini V3 STACK *1
Electrolytic capacito: 1000uF 35v *1
8pin to 8pin 1mm pitch 65mm cable *1
8pin to 8pin 1mm pitch 25mm cable *1
JST SH 6pin 150mm cable*1 ( The cable that goes to the CADDX Vista Air Unit is included.)
JST GHR 8pin to JST GHR 6pin 80mm cable*1 ( The cable that goes to the DJI Air Unit is included.)
JST GHR 8pin to JST GHR 6pin 150mm cable*1  ( The cable that goes to the DJI Air Unit is included.)
80mm SMA--MMCX Cable *1
60mm Antenna *1
150mm 4pin JST GH wire *1

Manual:

Kakute F7 mini V3 Manual
Holybro_Atlatl_HV_micro_Manual
Tekko32 F3 4in1 mini ESC(45A) SPEC

Some Tips:

BLHeli_32 ESC Firmware Overview
GitHub

Download:

ATLATL HV V2-VTx table

Maybe You Also Like...
Durandal
Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.
$205.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
SALE
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00 $170.00
Kakute F7 HDV Stacks
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$92.00
KakuteF7 HDV AIO
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$42.00
Kakute F7 AIO V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$49.00
Kakute F7 V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$45.00
KakuteF7 HDV
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$38.00
Pixhawk 4 GPS Module
SALE
Pixhawk 4 GPS Module with JST GH 10 Pin connector for Pixhawk 4 "GPS Module" input port
$42.00 $42.00
Kakute F4 All-In-One V2
The Holybro Kakute F4 AIO All-In-One flight controller makes it easy to build your multirotor.
$40.00
Kakute F4 V2
The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot.
$36.00
Pix32"Pixhawk" Flight Controller
This board is based on the Pixhawk project FMUv2 open hardware design. It is also know as Pixhawk 2,with hardware version px4 2.4.6.
$129.00