KakuteF7 HDV,Kakute F7

Product Details
Write a Comment(0)
After-sales Service

The port to the DJI air unit on KAKUTE F7 HDV and KAKUTE F7 HDV AIO have been optimized, the output voltage has increased to 9V/2A.

Overview

HolyBro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.

Features

Supports Betaflight.
High-performance / low-noise IMU. MPU6000 with 6-axis gyro and accelerometer.
Ready for autonomous flight: Integrated BMP280 barometer and SCL/SDA for use with external GPS/magnetometer units.
Dedicated bootloader button for easy firmware flashing.
Low-profile design fits into even very compact frames.
Input voltage 7v to 42v. Power the board directly from the flight pack, up to 6S (on “B+” pad only).
Automatic voltage monitoring. No need to run a separate vBat wire for voltage monitoring; the KAKUTE F7 HDV monitors voltage directly from the power supply.
Filtered voltage output for clean, noise-free video. 2 On-board regulators output 5V and 8V. 5V output up to 1.5A to power peripherals such as receiver, FPV camera, or LED strip. 9V output up to 2A to DJI FPV VTx.
Supports BLHeli pass-through for easy ESC upgrade and configuration.

Specifications

MCU: STM32F745 32-bit processor
IMU:MPU6000
Barometer: BMP280
USB VCP Driver (all UARTs usable simultaneously; USB does not take up a UART)
6 hardware UARTS (UART1,2,3,4,6,7)
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without “uninvert hack”.
Supports serial receivers (SBUS, iBus, Spektrum, Crossfire) only. PPM and PWM receivers are not supported.
TF card for Blackbox logging
Dimensions: 35x35mm
Mounting Holes: Standard 30.5mm square to center of holes
Weight: 8g

Package Includes:
FC board *1
M3 Anti-Vibration Silicone Grommet Insert *4
JST SH 8pin 150mm cable*1
JST GHR 8pin to JST GHR 6pin 80mm cable*1
JST GHR 8pin to JST GHR 6pin 150mm cable*1

Manual:
Holybro Kakute F7 HDV Manual

More relevant product options

https://shop.holybro.com/kakute-f7-hdv-stacks_p1220.html
https://shop.holybro.com/kakutef7-hdv-stackdji-digital-fpv-system_p1184.html

Maybe You Also Like...

Durandal

Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.

$205.00

Pixhawk4 mini

Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.

$139.00

Pixhawk 4

Pixhawk® 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.

$170.00

Kakute F7 HDV Stacks

Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module.

$92.00

KakuteF7 HDV AIO

Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module.

$42.00

X500 Kit

X500 Frame full carbon fiber twill，ARM diamete16mm, It is perfectly compatible with the Holybro Pixhawk4 and Pixhawk4 Mini kits.The kit is easy to assemble.No soldering needed.

$425.00