HomeHome > Peripherals > Power Distribution Boards(PDB)

Pixhawk 4 Power Module (PM07)

Item Code:
15008
Pihawk 4 Power Module(PM07)
Unit Price:
USD $33.00
Price:
USD
$33.00
Shipping Cost:
to
PC
977 in Stock
  • Product Details
  • Write a Comment(0)
  • After-sales Service

The Power Management Board (PM Board) serves the purpose of a Power Module as well as a Power Distribution Board. In addition to providing regulated power to Pixhawk 4 and the ESCs, it sends information to the autopilot about battery’s voltage and current supplied to the flight controller and the motors.

Specifications:

PCB Current: total 120A outputs (MAX)
UBEC 5v output current :3A
UBEC input voltage : 7~51v (2~12s LiPo)
Dimensions:68*50*10 mm
Mounting Holes:45*45mm
Weight: 47.5g

Make the PM07 show the quantity of electric charge of your battery

Mission Planner setup:

  1. Connect PM07 to the battery, also connect it to Mission Planner via USB.
  2. Click “INITIAL SETUP” and come to the menu “Battery Monitor”.
  3. Make “Monito” into “Analog Voltage and Current”.
  4. Make “Sensor” into “9: Holybro Pixhawk4 PM”.
  5. Make “HW Ver: "The Cube or Pixhawk" (pixhawk4,pixhawk4mini,pix32v5,pix32)”   
            “HW Ver:  Leave this blank(Durandal)”           
  6. Input “18.182” into Voltage divider (Calced).
  7. Input “36.364” into “Amperes per volt”.
  8. Disconnect and reconnect it to finish the setting up.(“Measured battery voltage” shows the current quantity of electric charge of the battery.)

HW Ver: "The Cube or Pixhawk" (pixhawk4,pixhawk4mini,pix32v5,pix32)

HW Ver:  Leave this blank(Durandal).Or you can desigante it in the Full Parameter List   
Command: BATT_CURR_PIN   Value: 17 
Command: BATT_VOLT_PIN   Value: 16

Package Include:

1x   PM07 board
1x   80mm XT60 connector wire (installed)
1x   Electrolytic capacito: 220uF 63V (installed)

2x   JST GH 10P Cable
1x   JST GH 8P Cable
2x   JST GH 6P Cable

Quick Start Guide

PM07-Quick-Start-Guide.pdf



Maybe You Also Like...
Spare Parts-Kopis cinewhoop 2.5inch
NEW
Applicable for Kopis cinewhoop 2.5inch(SKU30076,30077)
$8.00
Kopis cinewhoop_2.5inch(free shipping)
NEW
Nebula Pro Vista Kit 720p/120fps low latency HD digital FPV system / T-Motor: F1404 KV3800 / GEMFAN D63-5B / Take-off Weight:248g
$144.00
Tekko32 F3 4IN1 Mini 35A ESC(35A)
NEW
BLHELI32 / F3 MCU/4x 35A/20x20mm
$43.00
H-RTK F9P GNSS Series
NEW
Differential high-precision multi-band GNSS positioning system series. UBLOX F9P module
$378.00
H-RTK M8P GNSS Series
NEW
H-RTK M8P is the latest differential high-precision GNSS positioning system from Holybro. It uses a UBLOX M8P module.
$199.00
Pix32 v5
HolyBro Pix32 v5 is a new flight controller we have developed on the base of FMUv5 scheme, which can be regarded as a variant version of ‘Pixhawk4’.
$143.00
Durandal
Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.
$205.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00
Kakute F7 HDV Stacks
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module.
$92.00
KakuteF7 HDV AIO
Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module.
$42.00