HomeHome > Flight Controllers > Pixhawk4 mini

Pixhawk4 mini

Item Code:
20054,20055,20111,20112
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
Unit Price:
USD $139.00
Price:
USD
$139.00
Shipping Cost:
to
set
2033 in Stock
  • Product Details
  • Write a Comment(1)
  • After-sales Service


Pixhawk 4 Mini

The Pixhawk® 4 Mini autopilot is designed for engineers and hobbyists who are looking to tap into the power of Pixhawk 4 but are working with smaller drones. Pixhawk 4 Mini takes the FMU processor and memory resources from the Pixhawk 4 while eliminating normally unused interfaces. This allows the Pixhawk 4 Mini to be small enough to fit in a 250mm racer drone. The Pixhawk 4 Mini is easy to install; the 2.54mm (0.1in) pitch connector makes it easier to connect the 8 PWM outputs to commercially available ESCs.
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.

Product Features

  • Half the footprint of the Pixhawk® 4
  • The same FMU processor and memory resources as the Pixhawk 4
  • Aluminum casing for great thermal performance
  • Easy to connect to commercial ESCs
  • The latest sensor technology from Bosch® and InvenSense®
  • Redundant IMUs for reliable performance
  • NuttX real-time operating system
  • Pre-installed with the most recent PX4 firmware

Technical Specifications

  • FMU Processor: STM32F765
    • 32 Bit Arm® Cortex®-M7, 216MHz, 2MB memory, 512KB RAM
  • On-board sensors
    • Accel/Gyro: ICM-20689
    • Accel/Gyro: BMI055
    • Mag: IST8310
    • Barometer: MS5611
  • GPS: ublox Neo-M8N GPS/GLONASS receiver; integrated magnetometer IST8310

Electrical Data

Voltage Ratings

  • Power Brick Input: 4.75~5.5V
  • USB Power Input: 4.75~5.25V
  • Servo Rail Input: 0~24V
  • Max current sensing: 120A

Mechanical Data

  • Dimensions: 38x55x15.5mm
  • Weight: 37.2g
     

Package Included (SKU20054)

Pixhawk4 mini *1
Pixhawk4 GPS MODULE *1
PM06 V2 Power Management Board *1
I2C splitter Board *1
6 to 6 pin cable (power) *2
4 to 4 pin cable (CAN) *1
6 to 6 pin and 4 pin "Y"cable *1
6 to 6 pin cable(Debug) *1
PPM/SBUS out cable *1
XSR receiver cable *1
DSMX receiver cable *1
SBUS receiver cable *1
USB cable *1
'X'type folding pedestal mount  *1
70mm & 140mm carbon rod stand off *2
Foam Set *1
Pixhawk4 mini Quick Start Guide *1


Package Included (SKU20055)

Pixhawk4 mini *1
PM06 V2 Power Management Board *1
I2C splitter Board *1
6 to 6 pin cable (power) *2
4 to 4 pin cable (CAN) *1
6 to 6 pin and 4 pin "Y"cable *1
6 to 6 pin cable(Debug) *1
PPM/SBUS out cable *1
XSR receiver cable *1
DSMX receiver cable *1
SBUS receiver cable *1
USB cable *1
Foam Set *1
Pixhawk4 mini Quick Start Guide *1





Some Tips:

PX4 Docs

Downloads:

Pixhawk 4 Mini Wiring Quick Start
Pixhawk 4 Mini Technical Data Sheet
Pixhawk 4 Mini_Pinouts
Pixhawk4-GPS-Quick-Start-Guide

Ardupilot Stack:

Firmware
README


 
Maybe You Also Like...
Kopis cinewhoop_2.5inch(free shipping)
NEW
Caddx Nebula Vista Kit 720p/120fps low latency HD digital FPV system / T-Motor: F1404 KV3800 / GEMFAN D63-5B / Take-off Weight:248g
$144.00
Tekko32 F3 4IN1 Mini 35A ESC(35A)
NEW
BLHELI32 / F3 MCU/4x 35A/20x20mm
$43.00
H-RTK F9P GNSS Series
NEW
Differential high-precision multi-band GNSS positioning system series. UBLOX F9P module
$378.00
H-RTK M8P GNSS Series
NEW
H-RTK M8P is the latest differential high-precision GNSS positioning system from Holybro. It uses a UBLOX M8P module.
$199.00
Pix32 v5
HolyBro Pix32 v5 is a new flight controller we have developed on the base of FMUv5 scheme, which can be regarded as a variant version of ‘Pixhawk4’.
$143.00
Durandal
Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.
$205.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00
Kakute F7 HDV Stacks
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module.
$92.00
KakuteF7 HDV AIO
Kakute F7 HDV All-In-One is designed to work with the DJI FPV VTx module.
$42.00
X500 Kit
X500 Frame full carbon fiber twill,ARM diamete16mm, It is  perfectly compatible with the Holybro Pixhawk4 and Pixhawk4 Mini kits.The kit is easy to assemble.No soldering needed.
$425.00