HomeHome > Telemetry Radios > 433MHz

Transceiver Telemetry Radio V3

Item Code:
17012,17013,17014,17015
Pixhawk 4 compatibal
Unit Price:
USD $39.00
(0% OFF)
Price:
USD
$39.00
(0% OFF)
  • Telemetry Radio V3:
    100mW Telemetry Radio V3 433MHz 100mW Telemetry Radio V3 915MHz 500mW Telemetry Radio V3 433MHz 500mW Telemetry Radio V3 915MHz
Shipping Cost:
to
Delivery:
Estimated between
Units
199 in Stock
  • Product Details
  • Write a Comment(1)
  • After-sales Service

A Holybro Telemetry Radio is a small, light and inexpensive open source radio platform that typically allows ranges of better than 300m “out of the box” (the range can be extended to several kilometres with the use of a patch antenna on the ground). The radio uses open source firmware which has been specially designed to work well with MAVLink packets and to be integrated with the Mission Planner, Copter, Rover and Plane.
The radios can be either 915Mhz or 433Mhz and you should purchase the model which is appropriate for your country/region.


SPECIFICATIONS


Processing:
100 mW maximum output power (adjustable) -117 dBm receive sensitivity
Open-source SIK firmware
RP-SMA connector
2-way full-duplex communication through adaptive TDM UART interface
Transparent serial link
MAVLink protocol framing
Frequency Hopping Spread Spectrum (FHSS) Configurable duty cycle
Error correction corrects up to 25% of bit errors Open-source SIK firmware
Configurable through Mission Planner & APM Planner
FT230X is a USB to BASIC UART IC

 

Features
Interchangeable air and ground modules 915 or 433 mHz
Micro-USB port
6-position JST-GH connector

Dimensions
28 x 53 x 10.7mm (without antenna)
Power
Supply voltage: 5VDC (from USB or JST-GH)
Transmit current: 100 mA at 20dBm
Receive current: 25 mA

Serial interface: 3.3 V UART

 
Status LEDs
The radios have 2 status LEDs, one red and one green. The meaning of the different LED states is:
Green LED blinking - searching for another radio
Green LED solid - link is established with another radio
Red LED flashing - transmitting data
Red LED solid - in firmware update mode
 
Connecting to Pixhawk4
Use the 6 pin JST-GH connector that should have come with the radio to connect the radio to your Pixhawk4’s “Telem 1” (“Telem 2” can also be used but the default recommendation is “Telem1”).

Connecting to a PC
Connecting the radio to your Windows PC is as simple as connecting the micro USB cable (which should have been included with the radio) to your PC. The necessary drivers should be installed automatically and the radio will appear as a new “USB Serial Port” in the Windows Device Manager under Ports (COM & LPT). The Mission Planner’s COM Port selection drop-down should also contain the same new COM port.

Package Included:
radio modules with antennas *2
Micro-USB cable *1
Android OTG adapter cable *1
GH 6P-GH 6P cable *1
MLX 6P-GH 6P cable *1
SMA Adapter *2


Download
http://www.holybro.com/manual/Telemetry-Radio-V3-Quick-Start-Guide.pdf


Maybe You Also Like...
Durandal
Durandal is a new flight controller designed by Holybro utilizing the STM32H7 microcontroller series.
$205.00
Pixhawk4 mini
Pixhawk 4 Mini was designed and developed in collaboration with Holybro® and Auterion®. It is based on the Pixhawk FMUv5 design standard and is optimized to run PX4 flight control software.
$139.00
Pixhawk 4
SALE
Pixhawk​®​ 4 is the latest update to the successful family of Pixhawk flight controllers. It is designed and developed in collaboration with Holybro and Auterion, optimized to run PX4. It comes preinstalled with the latest PX4 firmware.
$170.00 $170.00
Kakute F7 HDV Stacks
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$92.00
KakuteF7 HDV AIO
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$42.00
Kakute F7 AIO V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$49.00
Kakute F7 V1.5
IMU updated to MPU6000,Re-designed and more reliable damping structure
$45.00
KakuteF7 HDV
Holybro Kakute F7 HDV is designed to work with the DJI FPV VTx module. The GH port available on the board makes it much more convenient for you to connect Holybro Kakute F7 HDV to the DJI FPV VTx, for both signal and power supply.
$38.00
Pixhawk 4 GPS Module
SALE
Pixhawk 4 GPS Module with JST GH 10 Pin connector for Pixhawk 4 "GPS Module" input port
$42.00 $42.00
Kakute F4 All-In-One V2
The Holybro Kakute F4 AIO All-In-One flight controller makes it easy to build your multirotor.
$40.00
Kakute F4 V2
The Holybro Kakute F4 flight controller supports important features of Betaflight/Cleanflight, such as OSD and Dshot.
$36.00
Pix32"Pixhawk" Flight Controller
This board is based on the Pixhawk project FMUv2 open hardware design. It is also know as Pixhawk 2,with hardware version px4 2.4.6.
$129.00